Disco Zebra Midgeling

• By Jason Hansen • Fly Tying


Disco Zebra Midgeling

The Disco Zebra Midgeling is a pattern derived from combining the Disco Midge pattern with Mike Mercer's successful Zebra Midgeling pattern. Mercer's pattern is based off of the ubiquitous Zebra Midge, which is about as simple as a pattern can get: a thread base, wire ribbing, and a metal bead head. Mercer modified the Zebra Midge by adding triggering characteristics to the fly to help entice reluctant trout to feed. In my fishing and tying of Mercer's pattern, I've found that I like to make two modifications to the pattern, especially for smaller sizes, that results in the Disco Zebra Midgeling.

The Disco Zebra Midgeling has proven to be an effective pattern drifted off a dry fly like a small caddis or Griffith's Gnat, as well as drifted deep as a dropper off a bigger nymph. For me, a red version of the fly has worked well on clear freestone streams as a dropper off a small dry. In multiple instances I've seen fish move more than one foot off their feeding lane to take the nymph. On a tailwater river with excellent midge populations, I've used both small black and light-blue Disco Zebra Midgelings drifted off the bottom and taken very good numbers of trout. The fly has out-produced standard nymph patterns many times for me, and is now a go-to fly in my box.


Zebra Midge

One of the changes Mercer made to the original Zebra Midge is he wrapped the fly body in clear tubing. I feel this makes the fly body too thick for most small midge patterns (#18 and smaller). Mercer also likes the use of ostrich herl for the fly collar behind the head; again, while this works for larger flies, the herl feels too large to me to be used on smaller patterns.



Disco Midge

The Disco Midge is a similarly simple pattern to the Zebra Midge, but instead of the thread body it uses flashabou to make a thin, colored, reflective body. I like the use of flashabou on the Disco Midge and substituted flashabou for the body of the Zebra Midgeling. The other change I like to do on Mercer's pattern is to use peacock herl instead of ostrich herl for the fly's collar. While it doesn't have the same movement as the ostrich herl, the peacock herl fits the fly's profile better while also adding some irresistable iridescence.

The following are the fly tying instructions for the Disco Zebra Midgeling.

Materials

Hook:Tiemco 2487, #16-#22
Thread:Uni 8/0
Tail:Angel Hair - Polar Ice
Body:Flashabou (black, red, olive, lt blue are most common)
Ribbing:Ultra Wire X-Small silver wire
Wing:Pearl Krystal Flash
Collar:Peacock Herl
Head:Bead (black bead for black, olive, lt blue bodies; copper bead for red flies)

Tying Instructions


1. Place the bead onto the hook, then attach the thread behind the bead.

2. Tie in a small clump of Angel Hair for the tail. Remember, a little goes a long ways. Trim the tail to be quite short, as shown.

3. With the thread at the rear of the hook, tie in the wire ribbing and wrap the thread back up to the eye of the hook. Leave the wire dangling off the back of the hook.

4. Tie in one strand of Flashabou at its half-way point directly behind the bead.

5. Wrap the Flashabou down the hook shank to the tail, covering the entire hook. Then wrap the Flashabou over itself, back to behind the bead, and tie off. The double wraps of Flashabou help increase the durability of the fly.

6. Rib the fly with wire and tie off the wire behind the bead.

7. Take one strand of Krystal Flash and bend it in half, aligning the ends. Tie the two ends in behind the bead. Then form a loop with the two strands and tie off at the same place behind the bead, forming two loop wings. The loop should be approximately half of the hook shank.

8. Tie in one sword of peacock herl and leave the thread back a few wraps from the bead.

9. Wrap the peacock herl forward to the bead then back to its starting point, three to four wraps total. To tie off, wrap the thread through the peacock herl once or twice so the thread ends up directly behind the bead. Trim the remaining peacock herl sword.

10. Whip finish and cut thread. If you like, you can coat the body of the fly lightly with Sally Hansen's Hard as Nails or some similar clear coat.

11. Catch some fish!

Views: 39376 • Comments: 1

Comments

Troy Pearse

Sweet pattern! It worked for me. :)

Closed for comments.